Current position > Contact Us
Quick Answer: Steam flow meter sinks combine rugged vortex or DP primary elements with local electronics for boiler room steam audits. Most plants in Southeast Asia, the Middle East, and Latin America need DN50 to DN150 lines, 8 bar to 16 bar steam, and 185 °C to 210 °C saturated steam. Send your pipe size, steam pressure, temperature, and flow range to Silver Automation Instruments for a direct price.
Boiler room audits catch steam leaks and failed traps. They also reveal oversized boilers. Many plants guess steam consumption because the existing orifice plates are old or the impulse lines get blocked. A paint plant in Vietnam found a 12 percent steam loss after installing a vortex meter on a DN80 header. The audit took one shift. The meter paid for itself in under five months.
But total steam flow data tells you where to start when trap surveys and pipe insulation checks are not enough. Wet steam and pipe vibration can hurt accuracy. Bad straight run also adds error. So we recommend vortex and DP systems with local displays and 4-20 mA HART outputs for these sites.
A vortex flow meter works well for steam from DN15 to DN200. It has no moving parts and supports process temperatures up to 350 °C with the right body and sensor. For saturated steam at 10 bar, a DN80 vortex meter typically covers 300 kg/h to 6000 kg/h. Accuracy is about 1.0 percent of reading for gases and steam. Output options include 4-20 mA HART, pulse, and RS485 Modbus. We can add PT100 temperature compensation for mass flow and totalized kg displays.
Some customers order a local indicator with a rugged housing. Boiler operators can read flow without walking back to a PLC. In a Saudi Arabia food factory, the steam line pressure was 12 bar and the pipe was DN100. We supplied a vortex meter with a PN40 flange rating and a local display. The pulse output fed a steam totalizer in the control panel.
DP systems still handle steam lines above DN200 or above 350 °C where vortex meters may need custom materials. Common primary elements are orifice plates, averaging pitot tubes, and flow nozzles. A DP transmitter reads differential pressure and sends a 4-20 mA HART signal. The flow calculation follows the square root relationship. We often pair the transmitter with a local flow computer or a paperless recorder.
For a boiler audit in a chemical plant in Mexico, the steam header was DN250, pressure 22 bar, and temperature 280 °C. The orifice plate and three-valve manifold system worked without issues. The installation included condensate pots on the impulse lines to protect the transmitter. DP systems need more maintenance than vortex meters, but they are easier to verify on site.
Straight run matters. For a vortex meter on steam, keep 15D upstream and 5D downstream from elbows, valves, and reducers. Add more upstream distance if a control valve sits near the meter. Install the meter on a horizontal line when possible. In practice, most engineers skip the full straight run check. That short straight run causes hidden bias in the audit numbers.
For DP systems, keep impulse lines short and equal. Use condensate pots for steam service. Vent all air from the wet legs before zeroing the transmitter. Many field errors come from wet legs that are not filled correctly. Vibration can cause false readings on vortex meters. Check for steam hammer and pipe support problems. Look at PRV stations near the meter. A bypass line helps if the audit meter must be removed during production. Tell us if the area is classified as ATEX Zone 1 or Zone 2.
Send your steam pressure in bar, temperature in °C, pipe size DN, flow range in kg/h, and installation location. Also report if the steam is saturated or superheated. Send photos of the pipe run if the space is tight. We will reply with a model, price, and delivery time from Silver Automation Instruments.
Contact us at Tel: +86-25-68650347, Whatsapp: +86-25-52155837, WeChat: +86 15365082610. You can also visit flow-meter.com.au for vortex flow meter and DP transmitter specifications.
Q: What is a steam flow meter sink?
A: In this context, a steam flow meter sink is a metering assembly built for boiler room audits. It includes the primary meter, local display, transmitter, and often a section of pipe with flanges.
Q: Which is better for steam audits, vortex or DP?
A: Vortex is better for DN15 to DN200 saturated steam. DP handles larger lines and higher temperatures. Both work. Send your line size and steam condition for a specific selection.
Q: Can I use a vortex flow meter for wet steam?
A: Wet steam reduces accuracy. Install a steam separator upstream or use a DP system with pressure and temperature compensation. For most boiler audits, saturated steam with dryness above 0.95 works fine.
Q: What straight run do I need?
A: For vortex meters, keep 15D upstream and 5D downstream from elbows, valves, or reducers. More is better when the pipe is crowded. For DP orifice plates, check the beta ratio and upstream flow disturbances.
Q: What is the delivery time?
A: Standard vortex and DP systems ship in 2 to 3 weeks from Silver Instruments. Custom flanges, local indicators, or hazardous area approvals may add one to two weeks.
